10 Mart 2009 Salı

vsep

While membrane-based separations of liquids from solids have enjoyed increasing popularity over the last 20 years, the technology has an inherent Achilles heel that affects all membrane devices: fouling. This long-term loss in throughput capacity is due primarily to the formation of a boundary layer that builds up naturally on the membranes surface during the filtration process. In addition to cutting down on the flux performance of the membrane, this boundary or gel layer acts as a secondary membrane reducing the native design selectivity of the membrane in use. This inability to handle the buildup of solids has also limited the use of membranes to low-solids feed streams.



To help minimize this boundary layer buildup, membrane designers have used a method known as tangential-flow or cross-flow filtration that relies on high velocity fluid flow pumped across the membranes surface as a means of reducing the boundary layer effect. (See Figure 1)

In cross-flow designs, it is not economic to create high shear forces, thus limiting the use of cross-flow to low-viscosity (watery) fluids. In addition, increased cross-flow velocities result in a significant pressure drop from the inlet (high pressure) to the outlet (lower pressure) end of the device, which leads to premature fouling of the membrane that creeps up the device until permeate rates drop to unacceptably low levels.




Instead of producing high cross flow, an alternative method for producing intense shear waves on the face of a membrane is developed. The technique is called Vibratory Shear Enhanced Processing (VSEP). In a VSEP System, the feed slurry remains nearly stationary, moving in a leisurely, meandering flow between parallel membrane leaf elements. Shear cleaning action is created by vigorously vibrating the leaf elements in a direction tangent to the faces of the membranes.

The shear waves produced by the membrane's vibration cause solids and foulants to be lifted off the membrane surface and remixed with the bulk material flowing through the membrane stack. This high shear processing exposes the membrane pores for maximum throughput that is typically between 3 and 10 times the throughput of conventional cross-flow systems. (See Figure 2, above)

The oscillation produces a shear at the membrane surface of about 150,000 inverse seconds (equivalent to over 200 G's of force), which is approximately 10 times the shear rate of the best conventional cross-flow systems. More importantly, the shear in a VSEP System is focused at the membrane surface where it is cost effective and most useful in preventing fouling, while the bulk fluid between the membrane disks moves very little.



Because VSEP does not depend on feed flow induced shearing forces, the feed slurry can become extremely viscous and still be successfully dewatered. The concentrate is essentially extruded between the vibrating disc elements and exits the machine once it reaches the desired concentration level. Thus, VSEP Systems can be run in a single pass through the system, eliminating the need for costly working tanks, ancillary equipment and associated valving.

The disc pack hold up volume of a system with 1,400 ft2 (130 sq. meters) of membrane area, is less than 50 gallons (189 liters). As a result, product recovery in batch processes can be extremely high.


Emulsified oil are serving as lubricant as well as coolant in various metal industries such as steel making and metal cutting. Disposal of emulsified fluid is a very tough environmental pollution issue. It has high COD and oil/water fully emulsified. Conventional bio-chemical treatment consumes large amount of chemicals and high running cost yet still requires multiple post-treatment steps. The disposal of solid cake will ultimately contaminate underground water. Conventional membrane treatment faces low flux and severe fouling issues. VSEP can simplify treatment process. It has high anti-fouling ability and high recovery ratio. Concentrate can be put as fuel and permeate can achieve discharge standard.

At startup, the VSEP system is fed with a slurry and the concentrate valve is closed. Permeate is produced and suspended solids in the feed are collected inside the VSEP filter pack. After a programmed time interval, valve on concentrate line is opened to release the accumulated concentrated solids. The valve is then closed to allow the concentration of additional feed material. This cycle repeats indefinitely.


Membrane selection is the single most important parameter that affects the quality of the separation. Other important parameters that affect system performance are pressure, temperature, vibration amplitude, and residence time. All of these elements are optimized during testing and entered into the programmable logic controller (PLC) which controls the system.

The operating pressure is created by the feed pump. VSEP machines can routinely operate at pressures as high as 500 psig (35 bar). While higher pressures often produce increased permeate flow rates, they also use more energy. Therefore, an operating pressure is used that optimizes the balance between flow rates and energy consumption.

The vibration amplitude and corresponding shear rate can also be varied which directly affects filtration rates. Shearing is produced by the torsion oscillation of the filter stack. Typically the stack oscillates with an amplitude of 3/4 to 1 1/4 inches (1.9 to 3.2 cm) peak to peak displacement at the rim of the stack. The oscillation frequency is approximately 53 Hz and produces a shear intensity of about 150,000 inverse seconds.

Feed residence time is set by the frequency of the opening and closing of the exit valve (valve one). The solids level in the feed increases as the feed material remains in the machine. Occasionally, a cleaner is added to the membrane stack and continued oscillation helps clean the membrane in minutes. This process can be automated and only consumes approximately 50 gallons (189 liters) of cleaning solution thus reducing cleaner disposal problems inherent with other membrane systems.

Control system

VSEP systems are supplied with internationally branded Programmable Logic Controllers. All components are fully contained in a NEMA 4 rated enclosure.

Various levels of control sophistication are available depending on the complexity of the application. For polishing or low solids applications simple controls having minimal outputs and inputs are provided. For high solids applications controls with more features are used to insure trouble free operation. The VSEP controller typically sets solids levels by actuating the exit valve based on operating parameters such as pressure or flow rate.

Other control options available include automatic clean-in-place, automatic flush, automatic shut down, full alarm features with digital diagnostic displays, remote diagnostics and monitoring, and many others. Dunwell engineers have spent years perfecting VSEP controls to maximize reliability and to minimize operator intervention.


Clean-In-Place

Clean-In-Place, CIP, is a package of pre-connected pipes, valves, tanks, pumps serving to clean the filter pack in steps by washing and flushing. Different cleaner can be applied according to different fouling chemistry. Piping has different material and different grade of polishing according to applications. One CIP can serve up to 6 i-series VSEP. Customer can choose either fully manual or fully automatic or somewhere in between according to individual application.

1 yorum:

Şükrü Yılmaz dedi ki...

Günaydın Yere düşen yağmur damlaları Kalbine inecek güneşi engellemesin Güneş bulutların arasından Hep sana doğru baksın Güneş güzellikler getirsin. http://sukruyilmaz.net/images/cuma2.jpg

Hayırlı Günler Cumanız Mubarek Olsun Ailenizle ve Sevdiklerinizle birlikte Huzurlu,Neşeli ve Bol Bereketli Güzel bir Cuma Günü geçirmenizi dilerim.Sevgiyle,Saygıyla vede Sağlıkla Mutlu Esen Kalın Allaha Emanet Olun,Saygılarımla.

ZALİM

Senin gözlerinde
Büyüttüm sevgimi
Gece gibi simsiyah gözlerinde
Aklımı alıp götüren yarim
Deli divane aşık ettin
Dert oldun başıma
Sabır taşına çevirdin beni zalim
Anlamadım neydim ne oldum
Gözlerinle vurdun beni zalim

Alıntı:Gülay Görgülü
http://www.siirdefteri.com/?sayfa=siir&siir_id=15328

Şükrü Yılmaz
Antakya-Hatay
http://sukruyilmaz.net